Wool brief

REDA — Quick specification

Purpose
Make a wool cloth request specific enough to answer

Quick specification

Quick specification for wool tailoring cloth — compare at least four dimensions
Dimension Review question Evidence or next step
Composition What wool percentage and which companion fibres are declared by mass? Keep the declaration with the cutting. Do not replace it with a collection name.
GSM What mass per square metre is the target, and what tolerance is acceptable? Name the specimen state. A nominal suiting weight is not a measured result.
Usable width What width can be cut, and how is selvedge treated? Agree the width on the piece or roll being discussed, not on a catalogue nominal.
Finish Is the face milled, clear, or awaiting a treatment decision? Match the finish state of the cutting to the finish named in the brief.
Read the wool brief preparation guide

Make the wool cloth identifiable

Open with a composition line, a weave description, or the identity of a cutting you already have. A familiar cloth name can help the reader find the conversation, but it should sit beside fibre content rather than instead of it. Say whether the cloth is pure wool or a blend, and name the second fibre if you know it. Add the face you expect to see: a dry clear worsted, a softer milled surface, or a flannel character. If the cutting in hand differs from the written target, describe the difference in handle or colour instead of assuming the two are the same item. Yarn count can help when you know the system. Do not convert New Metric count into denier by guesswork, and do not treat micron talk as a substitute for the percentage declaration. Unknown fields stay blank so the reply can fill them.

Use units the same way throughout

Write mass as grams per square metre and width in centimetres, and keep those units on every line of the brief. Separate cuttable width from the full width that includes selvedge, because a jacket pattern uses the former. If you only know a nominal width from a previous season, mark it as nominal. A tolerance belongs next to the target GSM; without it, two measurements can look like a conflict when they sit inside an agreed band. Piece length, when you have it, is a discussion figure in metres and should not be copied from an unrelated order. If a laboratory mass was taken on a conditioned specimen, say so. An unconditioned hand sample can read differently on a scale, and that difference is a method note rather than a quality verdict.

Explain the tailoring context

State the garment and the making steps that change the cloth choice. A fused jacket front, a floating chest, a trouser crease and a coat that will be steamed often are different contexts. Quantity and destination describe the request so a reply can be framed; they do not set a minimum, a ship date or availability. Keep the cloth target in one block and the commercial context in another so a shade question is not mixed with a delivery question. If you are comparing two existing reports, copy the method name, the specimen condition and the date into the message. Water-related wording, if any, must say whether you mean rain on the face or vapour through the cloth. For wool suiting, most briefs never need a coating or laminate line; leave that line out unless the construction truly has one.

Send one focused next question

A short brief can still be precise. List what you already know, which line is missing, and what would help you choose the next cutting. Examples of a single next question: confirm the blend ratio on a named cutting, compare two shade clippings from different lots, or check whether a stated width is cuttable. If reports are attached in words, include method and sample condition so the reader does not treat a target as a measured value. Ask for the missing fact without presenting it as a property the cloth has already met. The contact form is the place to send that question. Nothing on this page confirms stock, a sample dispatch or a bulk match.

Send this wool specification

Keep the reading notes beside the comparison

Use this page to prepare a question, not to supply a measured result. Write the known material reference first, then the decision that is still open. Method, specimen and scope stay attached to any figure that is already in hand. Unknown points stay questions.

Notes to keep with the page
NoteWrite thisLeave this open
MaterialComposition, construction and finish if knownAny value that has not been confirmed
DecisionThe comparison or approval the inquiry needsA conclusion the record does not support
EvidenceMethod, specimen and scope when a report existsA label used without that context
Next stepThe sample or document that would resolve the questionA promise about stock, certification or capacity